red circles on my 3d drawing in auto-cad

Topics covered in this Lesson:

Isometric Drafting Techniques

Isometic Drawing

Using Isometric commands is one of the simplest ways to give a 3-D representation while using merely ii-D commands. This has been the usual way of doing things earlier CAD immune true 3-D work to exist done. Many times an isometric drawing is used to compliment or give more information to a iii view orthographic drawing. Run into the sample below.

Standard Engineering Layout

You tin meet that it is a very simple drawing. This basic isometric drawing of the object gives a very practiced thought of what it looks like. If this is all that is needed then isometric works well. Unfortunately, as before long as you change anything, similar the block's height, you'll need to redraw all four views.

AutoCAD has a command called ISOPLANE which allows yous to easily draw at a 30 caste angle as needed for an isometric drawing. You tin switch between the 3 'isoplanes' (top, right, left) by using this command or by pressing the F5 key.

Command: ISOPLANE <ENTER>
Current isoplane: Right
Enter isometric plane setting [Left/Top/Right] <Left>: T <ENTER>
Electric current isoplane: Summit

Newer versions of AutoCAD have an Isoplane icon on the status bar. You tin can click this to enter Isometric Drafting Mode every bit shown below. You lot can also change your Isoplanes here (but F5 is faster).

Isodraft icon in AutoCAD

By invoking this command, AutoCAD is now set to depict on the top isoplane past default. Your other choices would be 50eft or Right. Your first exercise will be to draw the object shown in a higher place using isometric methods.

Do i - Isometric Drafting

Brainstorm a new drawing using the acad.dwt template

Create a layer called OBJECT and requite it a green color. Make this your current layer.

Type in DDRMODES to bring upwards the Drawing Aids dialog box. Brand your settings the same every bit what you see beneath (simply plough on Isometric Snap).

Drafting Settings Dialog Box

NOTE :
Recollect this dialog box for later on. When you are done with Isometric Drafting, open up this dialog box once again and alter the radio button from "Isometric snap" to "Rectangular snap" to go back to the regular drawing settings.

Press OK and y'all'll see that the grid is set for isometric drawing for the left isoplane in one/ii unit increments. Your crosshairs are at present angled to prove you which isoplane you are currently on and the Grid is laid out differently from what you lot may exist used to.

Brainstorm by cartoon the left side of the box (shown at the pinnacle of the lesson) using the line command. Ignore the hole at this bespeak. You will desire to apply the Direct Altitude Entry Arrangement for this practise and brand sure that you have Ortho ( F8) and Osnaps ( F3) turned on.

Switch to your right isoplane ( F5) and depict the right side.

Switch to your superlative isoplane ( F5) and draw the top view.

Create the angle lines to add the angled surface.

Switch dorsum to the left isoplane and get-go the ELLIPSE command. At the command prompt, printing I for isocircle. This will allow you to create an ellipse at the correct angle based on the radius of the circle in the orthographic cartoon. Use the Osnap to pick the right centre point.

Salvage your drawing in your CAD binder. (Y'all take a CAD Folder past now, correct?)

To dimension an isometric drawing, yous have to exercise a few things kickoff. Create a text style chosen Left, and give it a 30 o obliquing angle, then create another chosen right with a -30 o obliquing bending. Then create a new dimension manner that has the text aligned with the dimension line. After you have placed a dimension, use the DIMEDIT control to alter the obliquing angle of the dimension + or - 30 degrees. You may also need to use the backdrop to change the text in the dimension to left or right depending upon the orientation of the dimension.

Keep in heed that this is withal only 2nd. Think that in some instances, it may be quicker and easier to use this method rather than the more complex 3-D methods y'all'll be learning in the following lessons.

Extra Practice: Copy this cartoon using isometric drawing methods.

Extra Practice: Copy this cartoon using isometric drawing methods. If you desire to add the hidden lines, jump alee to Lesson 4-3 to learn virtually linetypes.

Video: Isometric Drafting

fun_facts_about Autocad_Autodesk

​​Fun fact: Autodesk, like many other software companies, was challenged by the effects of software piracy in the early 1990s. The company has prevailed in litigation to protect its copyrights, including a 1994 accommodate against Cadisys Corporation, the result of which was a $100,000 settlement in Autodesk'due south favor on May 23, 1994.

Please back up
MyCADsite.com
Give a donation!

Donate

support_mycadsite_tutorial

  • To cover this months server costs
  • Exceeding amounts will get to creating new content
  • ​​Even a penny will help​

Did you like the lesson? ​❤️

pattersonfacera.blogspot.com

Source: https://www.mycadsite.com/tutorials/level_3/isometric-drawing-in-autocad-3-2.html

0 Response to "red circles on my 3d drawing in auto-cad"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel